• Proven PerkinElmer HGA® graphite furnace delivers reproducible analytical results
• True double-beam design delivers fast start-up and exceptional long-term stability
• Cutting-edge fiber optics maximize light throughput for improved detection limits
• Removable burner assembly and new mixing chamber design to quickly switch between analytical techniques
• TubeView™ color furnace camera simplifies autosampler tip alignment and sample dispensing
• Intuitive WinLab32™ for AA software for enhanced laboratory productivity

System Design 

• The 900H (Flame/HGA) systems incorporate a true double-beam flame spectrometer and graphite furnace atomizer on a single instrument.
• Monochromator:  Littrow design with motorized drive for automatic wavelength selection and peaking.
• Wavelength Range: 190 – 900 nm. Diffraction grating: 1800 lines/mm blazed at 236 nm and 597 nm.
• Spectral Bandwidths:  User selectable automatic slit widths of 0.2, 0.7 and 2.0 nm at their optimized slit height.
• Detector:   Wide-range segmented solid-state detector, including a built-in low-noise CMOS charge amplifier array.
• Automatic Lamp Selection:  8-lamp mount with built-in power supplies for PerkinElmer® cableless Lumina™ hollow cathode and patented electrodeless discharge lamps. Computer-controlled lamp selection and alignment via WinLab32™ for AA software. Lamp elements and recommended operating currents are automatically recognized and set when using Lumina hollow cathode lamps.

Background Correction

• Deuterium Arc Lamp:  Built-in continuum source double-beam background correction using a high-intensity.

Flame Atomizer

• Gas Controls:  Fully computer-controlled with oxidant and fuel monitoring. Keyboard-activated remote ignition system with air-acetylene. Acetylene flow is automatically adjusted prior to the oxidant change when switching to or from nitrous oxide-acetylene operation.
• Safety Functions:  Interlocks prevent ignition if the proper burner head, the nebulizer/end cap, or the burner drain system is not correctly installed; the liquid level in the drain vessel is incorrect; or gas pressures are too low. Interlocks also will automatically shut down burner gases if a flame is not detected, or if any of the other interlock functions are activated. Provision is included for safe shutdown from all operating modes in the event of a power failure.
• Sample Introduction System:  Modular sample introduction system consisting of the quick-change spray chamber, burner  head and nebulizer units. Alignment of the flame in the light beam is fully automatic, using a motorized burner mount  for vertical and horizontal burner adjustment and automatic software-controlled self-optimization of the burner position. The optimization of the operating flame condition is also fully automatic and software-controlled. The introduction system is equipped with a high-strength inert mixing chamber, angled to ensure proper drainage. There is a choice of high sensitivity corrosion-resistant plastic nebulizer or durable stainless  steel nebulizer. The standard is all-titanium, 10-cm, single-slot burner head for air-acetylene operation.

Graphite Furnace Atomizer 

• Built-in fully computer-controlled Heated Graphite Atomizer (HGA®), with built-in integrated platform for ease-of-use for all the elements.
• An external protective gas stream around the graphite tube prevents the entrance of outside air to maximize tube life. An internal purge gas goes through the graphite tube to remove the volatilized matrix vapors during drying and thermal pretreatment. The two gas streams are computer-controlled independently. Pneumatic opening and closing of the furnace for easy tube change.
• Common Furnace Features:  Analytical programs with up to 12 steps can be set up. Each step can be programmed with the following parameters:
  • Temperature:   Ambient up to 2600 °C (up to 3000 °C with PinAAcle 900H) in steps of 10 °C
  • Ramp Time:   0 to 99 s in steps of 1 sec
  • Hold Time:  0 to 99 s in steps of 1 sec
  • Internal Gas Flow:  0 mL/min (gas stop), 50 mL/min (mini-flow), 250 mL/min (full flow); can be switched over to another type of gas (alternate gas).
  • Furnace Opening and Closing:  Pneumatically-operated by software command.
  • Required Inert Gas   Argon – inlet pressure 300 kPa (3 bar) minimum. Maximum gas consumption is 700 mL/min.
  • Water Coolant  A circulatory cooling system is recommended and can be chosen for the PinAAcle 900T, 900Z and 900H systems. When operating the 900T/Z/H furnace systems without the  circulatory cooling system, cooling water meeting the following specifications should be used: sediment-free drinking water; 20-40 °C; flow rate not less than 2 L/min; pressure between 2.5 and 4.5 bar; pH between 6.5 and 7.5; hardness not greater than 14°dH or 100 ppm.

Furnace Autosampler

• Furnace Autosampler:  Sampler Table: Installed in front of the furnace unit. Removable sample tray with 88 and 148 sampling positions for sample and reference solutions and 1 overflow container for  pipette washing. Minimum sample requirement: Ca. 0.1 mL.
• Dispensable Volume:   Sample and Reagent: 1-99 μL, selectable in increments of 1 μL.Max. dispensable volume is 99 μL (sample volume + reagent volume). Flushing volume is fixed at 1.3 mL.
• Electronics:   The autosampler is powered from the spectrometer and is software-controlled.

Data System

• Data Control System:  Complete PC control using WinLab32 for AA software operating under the Microsoft®Windows® 7. Provides complete control of the instrument and its major accessories plus data handling and storage.
• Data Handling:   Instrument readings linear in absorbance (-0.500 A to +2.000 A), concentration or emission intensity with continuously variable scale expansion from 0.01 to 100 times. Integration  times operator-selectable from 0.1 to 120 sec in increments of 0.1 sec. Reading modes include time-averaged integration, non-averaged integration (peak area), and peak-height measurement. Includes built-in statistics. Up to thirty (30) standards and a choice of proven calibration equations. Reslope of the analytical curve using a single operator-selected calibration standard. Built-in Ethernet interface for computer connection and use of optional accessories. Data collection time of up to 20 mins.

Physical Data – Instruments

• Dimensions and Weight (without controller and cooling system): 95 cm x  73 cm x  68 cm;   122 kg
• System Power Requirements:  230V (±10%), 50/60 Hz (±1%), single phase alternating current PinAAcle 900H: 7000 VA (maximum)
• Electrical Protection:   As defined in EN 61010-1; Insulation Class I; Installation Category II; Pollution Degree 2.
• Certification:  Designed and tested to be in compliance with the legal requirements for laboratory instruments. The instrument is developed and produced in compliance with ISO 9001 and  ISO 13485. WinLab32 for AA software provides required control parameters for GLP and instrument performance validation.
• Safety Standards:  EN 61010-1, EN 61010-2-061, CSA C22.2 No. 1010.1, CSA C22.2 No. 1010.2.061. The instruments bear the CE Mark and the CSA/NRTL Certification Mark.
• EMC Standards:  EN 61326, EN 55011, EN 61000-3-2, EN 61000-3-3.
• Environmental Requirements:  Ambient temperature: +10 °C to +35 °C. Relative humidity: 20 to 80% non-condensing.